By Plumbing Guide for Bathtub Installation
By Plumbing Guide for Bathtub Installation
Blog Article
On this page down the page you can get some good quality resources in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Mounting a tub isn't precisely brain surgery, however it does need solid plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a new one is likewise a moderately challenging project. If the old bathtub is conveniently easily accessible, the job can move quickly; if you have to open up a wall surface to eliminate the old tub and also place the new bath tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the work as well as fit trying it. Rather than hiring a service provider to take over a halfway-completed job, it is much better to take into consideration using one before you begin. Chances are you may need an expert plumber to make tube connections.
This write-up will certainly aid you set up a new bathtub in your shower room if you have actually currently acquired a new bathtub as well as don't need to transform the plan of your previous water system pipes.
Your devices and product checklist must comprise the following:
Planning for the Setup
To start with, the sustaining structure provided with the bath must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water supply. After doing so, turn on the faucets to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic because of the limited accessibility that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wooden boards under its feet, position the tub in the needed setting. The wood boards are helpful in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the tub until the level reviews level.
To install faucets, fit the bottom of the furthest adaptable tap port to the suitable supply pipe by making a compression join; then do the exact same for the other faucet.
Turn on the supply of water as well as examine all joints and also new pipework for leakages as well as tighten them if required. Load the bath tub and also examine the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the tub ought to wait up until the bathtub has actually been utilized a minimum of when as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin ensuring that the washers remain in area between the faucet and also the sink. Protect the faucet in position with the supplier supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The former kind needs to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, triggering the water to permeate the wall surface between the bath as well as the tiling, leading to issues with wetness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your components and installations. They are marketed in tubes and also cartridges, as well as are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked paper or soft rope. Remember to always fill the tub with water before securing, to enable the motion experienced when the bathtub remains in use. The sealant can break fairly early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily readily available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I stumbled upon that post about How to Install a Bathtub while doing a lookup on the internet. Do you know somebody who is excited about the subject? Do not hesitate to promote it. I praise you for your time. Visit again soon.
Check This Out Report this page